基于改进灰狼优化算法的涡扇发动机性能/喷流噪声综合优化控制研究

为保证整个飞行过程中满足噪声适航标准和飞行器的安全性,需要按照最严苛的噪声要求进行发动机设计,并留有很大的安全裕度,因而导致发动机的性能潜力未能得到发挥。本文对传统灰狼算法进行了改进,提出自适应概率变异策略,在优化过程中调整狩猎模式,提升了算法的全局搜索能力;基于该算法开展涡扇发动机性能/喷流噪声综合寻优控制研究,根据不同飞行需求对航空发动机性能进行优化,获得最佳控制量,在满足安全性和噪声指标的同时,提高发动机的性能。仿真结果表明,改进后的算法具有更好的全局寻优性能,最大推力模式下可提升推力13.45%,最小油耗模式可降低油耗3.19%,最低涡轮前温度模式可降低涡轮前温度2.07%。     

基于双火花塞点火策略的活塞式航空煤油发动机爆震控制

在一台650 mL单缸活塞式航空发动机上,针对双火花塞点火方式对活塞式航空煤油发动机的爆震控制进行了试验研究。结果表明:采用两个火花塞同步点火,且将点火提前角推迟可以有效的抑制爆震,同时燃烧放热率幅值逐渐降低,整体燃烧相位逐渐推迟;采用双火花塞异步点火随着点火提前角点火相位差的增加,爆震强度逐渐降低,通过匹配主火花塞点火提前角与副火花塞点火提前角可进一步提升发动机的动力性。      

多机并联火箭羽流流场及其底部热环境分析

For the problem that the plume flow field structure of a multi engine parallel rocket is complicated and the bottom thermal environment is extremely harsh, which may cause the failure of the engine structural components, the plume flow field and thermal environment at different altitudes are studied through numerical simulation. The result is compared with the measured results in flight which shows that when the rocket is flying at a low altitude, the plume of the engines do not interfere with each other. As the flight altitude increases, the plumes gradually expand and begin to interfere with each other, and finally there is an obvious backflow at the bottom of the rocket. The maximum heat flux at the moment of take off is basically the same as the measured value in flight. Before the backflow occurs, the heat flux mainly consists of radiant heat, the convective heat flow increases as the flight altitude grows, but it is also much smaller than the peak heat flow at takeoff. The result has certain guiding significance for the optimal design of engine structure thermal protection.     

某发动机调节器自动检测异常故障分析

针对某型发动机自动调节器自动检测异常的故障现象,对产生发动机自动调节器自动检测异常的原因进行了深入地研究分析,并提出了针对性的预防措施。     

Experimental analysis of the breakage of a liquid bridge under microgravity conditions

The experimental results obtained in experiment “STACO” made on board the Spacelab D-2 are re-visited, with image-analysis tools not then available. The configuration consisted of a liquid bridge between two solid supporting discs. An expected breakage occurred during the experiment. The recorded images are analysed and the measured behaviour compared with the results of a three dimensional model of the liquid dynamics, obtaining a much better fit than with linear models.     

发动机试验液氢流量测量不确定度评定

针对某型号液体火箭发动机试验,介绍了液氢低温流量测量系统组成及原理。根据液氢质量流量测量数学模型,分析影响液氢流量测量不确定度的主要压力对贮箱容积的影响因素,依据不确定度评定相关标准和方法,对各种影响因素进行分析,最终得出液氢质量流量扩展不确定度为±0.88%,满足发动机设计部门对液氢低温质量流量测量不确定度±1%的要求。     

Thermal-structural analysis of regenerativelycooled thrust chamber wall in reusable LOX/Methane rocket engines

To predict the thermal and structural responses of the thrust chamber wall under cyclic work,a 3-D fluid-structural coupling computational methodology is developed.The thermal and mechanical loads are determined by a validated 3-D finite volume fluid-thermal coupling computational method.With the specified loads,the nonlinear thermal-structural finite element analysis is applied to obtaining the 3-D thermal and structural responses.The Chaboche nonlinear kinematic hardening model calibrated by experimental data is adopted to predict the cyclic plastic behavior of the inner wall.The methodology is further applied to the thrust chamber of LOX/Methane rocket engines.The results show that both the maximum temperature at hot run phase and the maximum circumferential residual strain of the inner wall appear at the convergent part of the chamber.Struc tural analysis for multiple work cycles reveals that the failure of the inner wall may be controlled by the low-cycle fatigue when the Chaboche model parameter γ3 =0,and the damage caused by the thermal-mechanical ratcheting of the inner wall cannot be ignored when γ3 ＞ 0.The results of sen sitivity analysis indicate that mechanical loads have a strong influence on the strains in the inner wall.     

Nutation instability of spinning solid rocket motor spacecraft

The variation of mass,and moment of inertia of a spin-stabilized spacecraft leads to concern about the nutation instability.Here a careful analysis on the nutation instability is performed on a spacecraft propelled by solid rocket booster (SRB).The influences of specific solid propellant designs on transversal angular velocity are discussed.The results show that the typical SRB of End Burn suppresses the non-principal axial angular velocity.On the contrary,the frequently used SRB of Radial Burn could amplify the transversal angular velocity.The nutation instability caused by a design of Radial Burn could be remedied by the addition of End Burn at the same time based on the study of the combination design of both End Burn and Radial Burn.The analysis of the results proposes the design conception of how to control the nutation motion.The method is suitable to resolve the nutation instability of solid rocket motor with complex propellant patterns.     

RBCC发动机火箭推力增益之探讨

为提高火箭基冲压组合循环(RBCC)发动机火箭冲压模态下火箭推力增益,基于模拟飞行Ma=4来流条件的数值计算结果,分析了火箭射流与冲压主流超/超剪切流动的特性,探讨了火箭推力增益的组成,并给出了提高火箭推力增益的措施:1)冲压流道、火箭工作参数的选取必须确保两股超声速剪切流之间的流动匹配,在有限空间内快速、低损的实现高能火箭射流与低能冲压主流间的动量及质量输运,最大限度地提高发动机喷管排气速度及压力;2)采用高室压火箭,通过增加推力室室压,提高火箭燃气膨胀程度,减小火箭推力增益损失。     

面向客机总体设计的涡扇发动机分析模型

建立一种用于估算涡扇发动机特性的工程分析模型，该模型以涡喷发动机推力估算模型与涡扇发动机效率分析方法为基础，引入高涵道比涡扇发动机的循环分析方法进行修正。利用该模型可以获取涡扇发动机的推力和油耗特性，进而考察总体循环参数对发动机性能的影响。通过与文献验证数据对比，判定了分析模型的精度。该模型只需要输入少量参数就可以快速完成计算过程，适合于飞机总体设计阶段，可以评估涡扇发动机参数对飞机性能的影响。